Showing 13–24 of 53 results
- Controls the start-up sequence and monitors the flame of up to 20 individual burners
- Dynamic on-board testing checks for faulty relays, proof of valve closure, high-fire and low-fire switch interlocks and shorted air switch
Read more
This product is already in your quote request list.
- Sensor module that activates a relay when a flame is detected by an ultraviolet sensor or a flame rod
- UL recognized & FM approved
- Plugs into an industry standard 11-pin base
- Test point at the front permits direct reading of the flame signal level, 0-12 V DC
Read more
This product is already in your quote request list.
- Monitoring, diagnosis, troubleshooting and control of single burner systems with individual valve trains
- Purge, no-purge and modulation models are available
- Meets UL and FM standards
- Fireye SB-Series Flame Safeguard Controls replace all Eclipse Veri-flame.
Read more
This product is already in your quote request list.
- Feature high ultraviolet (UV) sensitivity for monitoring gas or oil flames which cycle on and off frequently
- Check for a short-circuited or “run-away” scanner at the beginning and end of each flame cycle
- UL listed, CSA certified and FM approved
- Safeguarded against reverse connection, the 90° UV scanner operates with 6000 Series Multi-Flame and 6500 Series controllers
- Fireye UV scanners replace Veriflame scanners.
Read more
This product is already in your quote request list.
- Monitors: low gas, high gas, and low air pressure switches
- Pre-purge/post-purge fan and air valve control
- Optional integrated ignition transformer
- Optional PROFIBUS communications
- Integrated front panel display indicates fault and operating status
- Manual-mode operation for initial burner set-up
- Front Panel PC interface for programming diagnostics, and data logging
- Approvals: CE, CSA, FM and UL
Read more
This product is already in your quote request list.
- For burners in intermittent operation or in continuous operation
- Flame control by UV, ionization or a further option of using the furnace chamber temperature
- Display of the program status, unit parameters and flame signal; manual mode for burner adjustment and for diagnostic purposes
- Visualization and adaptation to the specific application via the PC programming and diagnostic software BCSoft to simplify logistics management.
- Air valve control on BCU..L relieves the furnace control
- Optional PROFIBUS DP interface
- Replaces the local control cabinet
- EC type-tested and certified
- Certified for systems up to SIL 3 and compliant with PL e
Read more
This product is already in your quote request list.
- For pilot and main burners in intermittent or continuous operation
- Replace the local control cabinet
- Flame control by UV, ionization or a further option of using the furnace chamber temperature
- Display of the program status, unit parameters and flame signal; Manual mode for burner adjustment and for diagnostic purposes
- Visualization and adaptation to the specific application via the PC programming and diagnostic software BCSoft to simplify logistics management
- Air valve control relieves the furnace control
- Optional PROFIBUS DP interface
- EC type-tested and certified
- Certified for systems up to SIL 3 and compliant with PL e
Read more
This product is already in your quote request list.
- For monitoring and controlling modulating individual burners and forced draught burners of unlimited capacity
- For directly ignited burners or burners ignited by a pilot burner in intermittent or continuous operation
- It is installed on a DIN rail in the control cabinet
- Perform safety functions in accordance with EN 746-2 and EN 676
- With optional valve proving system
- Flexible range of applications due to parameterization possibilities
- Optional bus module for fieldbus connection
- Safety functions up to SIL 3 (DIN EN 62061) corresponding to PL e (ISO EN 13849)
- Approvals: CE, CSA and UL
Read more
This product is already in your quote request list.
- For directly ignited burners of unlimited capacity in continuous operation pursuant to EN 746-2
- Replacement for the IFS 258
- Continuous self-testing for faults
- Immediate fault lock-out or restart following flame failure available as a switchable function
- Flame control with UV sensor or ionization sensor
- Diverse installation possibilities via holes or snap mechanism for DIN rail
- Space-saving installation on site with IFD 258..I with integrated ignition
- Display for program status and flame signal intensity
Read more
This product is already in your quote request list.
- Flame control by means of flame rod or UV-detector
- Flame simulation check before starting and after switching the burner off
- Suitable for ignition and ionisation control with one electrode
- Modern technique using semiconductors
- High cycling frequency
- Remote reset
- External fault indication
- FM approved
Read more
This product is already in your quote request list.
- For flame detection
- For multi-flame control for intermittent operation in conjunction with the flame control units IFS
- Ionisation or UV control
- Potential-free change-over contacts
- Integrated flame control signal
Read more
This product is already in your quote request list.
- Suitable for small burners due to high sensitivity
- Virtually immune to interference due to its insensitivity to daylight, infrared radiation and incandescent bulbs
- Maximum safety thanks to protection against discontinuity or short circuit on the flame signal cable
- Lower logistics costs as the UVS 10 replaces several previous models
- Suits industrial needs due to robust design
- Complies with the requirements of EN 298 in conjunction with Kromschroder automatic burner control units
Read more
This product is already in your quote request list.